Step 1 Mouse




• Remove the "Q.C. Passed" Sticker to have access to the Phillips screw below.
• Pull of the two upper mouse feet. It's enough to just remove half of the mouse feet to get to the screws.
• It is useful to pull of the mouse feet with the adhesive film.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 2

• Remove the three Phillips screws.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 3
• Lift the upper part of the mouse.
• Fold the upper and the lower part back like a book and put it aside.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 4
• Loose the plug with the flat end of a spudger.
• Pull the plug.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 5
• Lift the two side parts and put it aside.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 6
• Loose the plug with the flat end of a spudger.
• Pull the plug.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 7
• There are two plasic clips. Loose the left plastic clip very carefully.
• Fold the board up from the left side.
• Take out the board and put it aside.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 8
• Move the mouse wheel a bit to the right.
• Take the mouse wheel out of the guide forks.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 9
• Reference picture of the board.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 10
• Remove the four Phillips Screws.
• Remove the weight.
• Remove the board.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 11 optional for cleaning
• Have a look at the plastic clips
• Plastic clips for the black upper part for clicking.
• Plastic clips for the DPI button.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 12
• Insert the flat end of the spudger into the gap between the two halves on the left and right. The rear plastic clips should then release automatically.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 13
• Loose the plastic clips in the middle.
• Insert the spudger from the left and right side between both parts. The plastic clips should release automatically form their rest postion.
• Alle plastic clips are now released.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 14
• Insert the flat end of a spudger into the gap between the two parts.
• Increase the gap all around until the pieces fall apart.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 15
• Unlock the two plastic clips.
• Use the flat end of a spudger to lift and remove the DPI button.
Translate
One comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 16
• Overview of all parts.
Translate
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

<iframe id="dozuki-embed-173617" src="https://www.ifixit.com/Guide/embed/173617/full" width="800" allowfullscreen frameborder="0"></iframe> <script>window.addEventListener("message",function(a){var b=document.getElementById("dozuki-embed-173617"),c=a.data[0],d=a.data[1];switch(c){case"setHeight":b.style.height=d+"px"}},!1);</script> <iframe src="https://www.ifixit.com/Guide/embed/173617" width="800" height="584" allowfullscreen frameborder="0"></iframe>

Preview