iMac Intel 21.5" EMC 2805 AirPort/Bluetooth Card Replacement

Step 1 Display Assembly


Tool used on this step:
iMac Intel 21.5" Cardboard Service Wedge
$4.99
Buy
• With the hinge free to move, the iMac will be unbalanced and hard to work on. Repairs are fast and easy with an iMac service wedge, but can be completed without one.
• If you are using the iFixit cardboard service wedge, follow these assembly directions to put it together.
• Before beginning any work on your iMac: Unplug the computer and press and hold the power button for ten seconds to discharge the power supply's capacitors.
• Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply. Only handle the board by the edges.
Edit
9 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 2



• Starting on the left of the display, near the power button, insert the iMac Opening Tool into the gap between the glass panel and the rear enclosure.
• The hub on the iMac Opening Tool will keep you from pushing the wheel in too far. If using a different tool, insert no more than 3/8" into the display. Otherwise, you risk severing antenna cables and causing serious damage.
Edit
6 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 3
• Use the tool like a pizza cutter—roll it along through the gap, and it will cut the foam adhesive through the center.
• Be sure to always push with the handle behind the cutting wheel. If you pull, the wheel might get pulled out of the handle.
• Run the tool up along the left side of the display.
Edit
2 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 4
• Continue running the tool up around the top left corner.
Edit
One comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 5
• Cut the adhesive along the top left of the display.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 6
• Continue along the top of the display.
• You may want to run the tool back and forth through what you've already cut a few times, to ensure you get as much of the adhesive separated as possible.
Edit
8 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 7
• Push the tool around the top right corner of the display.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 8
• Wheel the tool down along the right side of the display.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 9
• Finish pushing the opening tool to the bottom of the right side of the display.
• At this point, you'll want to run the tool back around the entire display, to ensure you cut as much adhesive as possible.
Edit
3 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 10

Tool used on this step:
Plastic Cards
$2.99
Buy
• While the opening tool cut most of the adhesive, the display will still be slightly adhered to the case. A plastic card will be necessary to free up the last of this adhesive.
• Set the iMac face-up on a table.
• Starting from the top right corner of the iMac, wedge a plastic card between the display and frame.
• Be careful not to insert the plastic card more than 3/8", or you may damage internal components.
Edit
6 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 11
• Gently twist the plastic card sideways to create a gap between the display and frame.
• Move slowly and be careful not to stress the display glass too much—you only need to make a gap of about 1/4".
Edit
One comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 12
• Slide the card toward the center of the display to cut any of the remaining adhesive along the top right corner of the iMac.
• Be sure to stop before the iSight camera, or you may damage it.
Edit
2 comments
Add a comment
Add Comment
1024
Cancel Post comment
Step 13
• Wedge the plastic card into the top right corner once again, and leave it there to prevent the adhesive from resticking.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 14
• Insert a second plastic card into the gap between the display and frame near the top left corner of the iMac.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 15
• Gently twist the card upward, slightly increasing the space between the display and frame.
• As with the other side, twist slowly to allow the adhesive time to separate, and be careful not to over-stress the display glass.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 16
• Slide the plastic card toward the center, again stopping just before the iSight camera.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 17
• Wedge the plastic card back into the top left corner.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 18
• With both plastic cards inserted as shown near the corners, gently twist the cards sideways to increase the gap between display and case.
• If there are any sections that seem to stick and won't separate, stop twisting and use one of the cards to cut the remaining adhesive.
• Begin to lift the top of the display up from the frame.
• Only lift the display a few inches—the display data and power cables are still connected to the logic board.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 19 Display Assembly Cables

Tool used on this step:
Tweezers
$4.99
Buy
• Use a pair of tweezers to flip up the metal retaining bracket on the display data cable.
• Carefully pull the display data cable from its socket on the logic board.
• Be sure to pull the display data cable connector straight out of its socket.
Edit
One comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 20
• While holding the display up with one hand, use the other hand to unplug the display power cable.
• Lift the display up enough to have easy access to the connector, but not so much that you stretch the cables and stress their connections (about 8").
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 21 Display
• Lift the display up to a near-vertical position.
• At this point there is still a strip of adhesive along the bottom of the display, that will hold the display to the frame like a hinge. You can loosen this adhesive by working the display up and down a few times.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 22

Tool used on this step:
Plastic Cards
$2.99
Buy
• Be very careful not to touch the capacitor leads or any exposed solder joints on the back of the power supply (boxed in red).
• Grasp the small tab at the end of one of the bottom edge display adhesive strips and pull the adhesive toward the top of the iMac to remove it.
• Repeat this step with the other adhesive strip and remove it.
• If either adhesive strip breaks before it's removed, use a plastic card to slice through the remaining adhesive.
Edit
One comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 23
• Lift the display up from the frame and remove it from the iMac.
• It may be necessary to slowly lift from one side, to peel against the remaining adhesive.
• Be very careful handling the display—it's big, heavy, and made of glass.
• If you're replacing the display with a new one, you may need to transfer some components from the old display to the new display.
• During reassembly, head over to our display adhesive guide to install the new adhesive.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 24 AirPort/Bluetooth Card
• If necessary, use the tip of a spudger to peel back the tabs covering the antenna connectors.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 25
• Some models use two Torx screws to fasten the antenna cables to the AirPort card.
• If your iMac has these two screws, remove them now.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 26
• Use a spudger to pry each of the four antenna connectors straight up off their sockets on the AirPort/Bluetooth card.
• Note the original positions for each connector when reconnecting the cables.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 27
• Remove the two 3.2 mm T5 screws securing the AirPort/Bluetooth card to the logic board.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 28
• Push the AirPort/Bluetooth card slightly downwards, 1-2 mm at most.
• With a firm grip on the edges of the AirPort/Bluetooth card, pull it straight out of its socket on the underside of the logic board.
• Do not use excessive force to pull the end of the AirPort/Bluetooth card away from its socket on the logic board. Doing so may cause severe damage.
• Try not to touch the antenna connector sockets with your fingers, as the oils can corrode the metal and prevent good contact.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment
Step 29
• During reassembly, it may be a bit of a challenge to reinstall the AirPort/Bluetooth card as the socket is on the underside of the logic board.
• The AirPort/Bluetooth card socket is located a few centimeters below and to the left of the right speaker connector (highlighted in red), on the opposite side of the logic board.
• If the AirPort/Bluetooth card is properly seated, its screw holes should align with those on the logic board.
Edit
Add a comment
Add a comment
Add Comment
1024
Cancel Post comment

Author

with 4 other contributors

Walter Galan

701,042 Reputation

1,203 Guides authored

Badges: 54

• 
• 
• 

+51 more badges

Embed this guide

Choose a size and copy the code below to embed this guide as a small widget on your site / forum.

Preview