Fix Your Stuff Community Store

Jura Impressa F50 grinder replacement (TOTAL)

Introduction

Your fully automatic coffee machine makes very loud noises when grinding the coffee beans?

When making coffee, does the coffee only come out in drips?

Then you may have a problem with the grinder of your Jura Impressa F50 fully automatic coffee machine.

These instructions are intended to help you get access to the grinder of your fully automatic coffee machine in order to service it or to replace it completely.

It consists of a total of 3 parts: opening the machine, removing the grinder and reassembly.

What you need

  1. Jura Impressa F50 grinder replacement (TOTAL), Open Case: step 1, image 1 of 3 Jura Impressa F50 grinder replacement (TOTAL), Open Case: step 1, image 2 of 3 Jura Impressa F50 grinder replacement (TOTAL), Open Case: step 1, image 3 of 3

    • Clean the coffee machine before starting as well as possible and remove any remaining coffee bean debris, etc.

    • Pull the power plug before working on the coffee machine!

    • Never submerge the coffee machine completely under water.

    • Remove the drip pan, tray and container for used coffee,...

    • ... the water tank, ...

    • and the aroma protection cover.

    Translate

  2. Jura Impressa F50 grinder replacement (TOTAL): step 2, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 2, image 2 of 2

    • One hurdle: the back is attached with four special oval-head screws. They look like rivets. To remove them, you need an oval-head bit. In a pinch, you can also use a good pair of pliers.

    Translate

  3. Jura Impressa F50 grinder replacement (TOTAL): step 3, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 3, image 2 of 2

    • Remove the two T15 Torx screws from the coffee machine housing cover.

    Translate

  4. Jura Impressa F50 grinder replacement (TOTAL): step 4, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 4, image 2 of 2

    • Remove the top cover of the coffee machine.

    Translate

    • Remove the panel from the right side.

    • Slightly lift the side panel at the back and then pull it out backwards with a little effort. Especially when disassembling it for the first time, the force required for this can be quite high.

    Translate

    • Remove the left side panel.

    • A light tap on the back of the recess for the water tank can help to loosen the side panel.

    Translate

    • Remove the lock washer on the axle for grinding degree adjustment using pliers.

    • Removing the lock washer requires some force. Don't hesitate to pull firmly.

    Translate

    • Remove the grinding degree adjustment axle by using pliers to pull it upwards.

    Translate

  9. Jura Impressa F50 grinder replacement (TOTAL): step 9, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 9, image 2 of 2

    • Remove the 2 screws on the bean container of the coffee machine with the Torx T10 screwdriver.

    • The screws are in a recess.

    Translate

  10. Jura Impressa F50 grinder replacement (TOTAL): step 10, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 10, image 2 of 2

    • Remove the bean container.

    Translate

  12. Jura Impressa F50 grinder replacement (TOTAL): step 11, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 11, image 2 of 2

    • Remove the pinion for the grinding degree adjustment.

    Translate

  13. Jura Impressa F50 grinder replacement (TOTAL): step 12, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 12, image 2 of 2

    • Remove the 3 screws attaching the grinding mill attachment to the grinder with the Torx T10 screwdriver.

    Translate

  14. Jura Impressa F50 grinder replacement (TOTAL): step 13, image 1 of 1

    • Make sure not to rip any cables in this step.

    • Carefully lift up the grinder.

    Translate

    • Disconnect the first connector (black cable) from the plug-in connector attached to the bottom of the grinder.

    • After you have removed the plug, you can carefully set down the grinder. For the next step you will need both hands.

    Translate

    • Separate the second (white) cable attached to the grinder from the housing of the plug-in connector.

    • Carefully press on the housing of the plug-in connector.

    Translate

    • Remove the grinder to clean or replace it.

    Translate

    • Avoid putting the grinder down completely in this step, but hold it in your hand.

    • Reinstall the new or repaired grinder into the coffee machine.

    • Reconnect the grinder to the connectors. Make sure to place the connectors in the correct place.

    Translate

  19. Jura Impressa F50 grinder replacement (TOTAL): step 18, image 1 of 1

    • Now set the grinder back into its correct position

    Translate

  20. Jura Impressa F50 grinder replacement (TOTAL): step 19, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 19, image 2 of 2

    • Reattach the 3 screws for grinding mill by fastening them to the inserted grinder with the Torx T10 screwdriver.

    Translate

  21. Jura Impressa F50 grinder replacement (TOTAL): step 20, image 1 of 1

    • Reinsert the pinion.

    • Make sure that the marking aligns with the center of the grinder, as the pinion is used to adjust the grinding degree and hence the strength of the coffee.

    Translate

    • Reinsert the bean container into the coffee machine.

    Translate

  23. Jura Impressa F50 grinder replacement (TOTAL): step 22, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 22, image 2 of 2

    • Fasten the two screws we remove from the bean container earlier with the Torx T10 screwdriver.

    Translate

    • Reinsert the axle for grinding degree adjustment.

    Translate

    • Use pliers to reseat the safety washer.

    Translate

    • Reinstall the left side panel.

    • Put on the side wall and make sure that the lugs are snapped into the slots provided. Then slide the side panel slightly forward. The side panel should audibly snap into place when pushed forward.

    Translate

    • Reinstall the right side panel.

    • First attach the side wall and make sure that the lugs have snapped into the slots provided. Then slide the side panel slightly forward. The side panel should audibly snap into place when pushed forward.

    Translate

  28. Jura Impressa F50 grinder replacement (TOTAL): step 27, image 1 of 1

    • Place the housing cover back on the coffee maker.

    Translate

  29. Jura Impressa F50 grinder replacement (TOTAL): step 28, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 28, image 2 of 2

    • Use the Torx T15 screwdriver to tighten the 2 countersunk screws on the housing cover.

    Translate

  30. Jura Impressa F50 grinder replacement (TOTAL): step 29, image 1 of 2 Jura Impressa F50 grinder replacement (TOTAL): step 29, image 2 of 2

    • Using the oval head wrench, tighten the 4 oval head screws on the back of the machine.

    Translate

  31. Jura Impressa F50 grinder replacement (TOTAL): step 30, image 1 of 3 Jura Impressa F50 grinder replacement (TOTAL): step 30, image 2 of 3 Jura Impressa F50 grinder replacement (TOTAL): step 30, image 3 of 3

    • Replace the water tank,

    • the drip tray with drip tray, pulp tray and pulp container,

    • and place the aroma protection cover back on.

    Translate
Finish Line

7 other people completed this guide.

Special thanks to these translators:

de en

100%

Annika Faelker

Disassembled

These translators are helping us fix the world! Want to contribute?
Start translating ›

Attached Documents

Author

with 3 other contributors

Natalie

Member since: 05/08/19

747 Reputation

4 Guides authored

Badges: 9

+6 more badges

Team

KMM 2019SS Member of KMM 2019SS

Community

11 Members

16 Guides authored

0 Comments

Add Comment

View Statistics:

Past 24 Hours: 6

Past 7 Days: 44

Past 30 Days: 209

All Time: 9,427